Proton Wira modifications under RM1K project: Part 2

Proton Wira modifications under RM1K project: Part 2 - Hello my friend Cars Gallery, In the article you read this time with the title Proton Wira modifications under RM1K project: Part 2, we have prepared this article well for you to read and take the information in. Let's hope that the contents of the post Articles accessories, Articles audio, Articles diy, Articles modifications, Articles wiraproject, as we write to you, you can understand. Okay, good reading.

Title : Proton Wira modifications under RM1K project: Part 2
link : Proton Wira modifications under RM1K project: Part 2

Read also


Proton Wira modifications under RM1K project: Part 2

This is a very long overdue update on my Proton Wira modifications under RM1K project.

Picking up from what I last posted, the Proton badge (meant for Proton Iswara) finally arrived but there was a problem. The original was a screw-on badge while the new one was a stick on and somehow I could not find a way to get it to stick properly on the original place. So I came up with an idea. Was not sure whether it would work but fortunately it did. I peeled off the plastic logo and super glued it on to the original screw-on base.





I also bought a new Proton Manual Car Leather Gear Knob Carbon With R3 stitching on the sides for RM50/, also from a seller on Lelong.


Definitely a great improvement on the original rounded plastic knobs which were worn out. This brought me to a new total of RM363.90.

Thinking of what to do next, I thought about the faulty reverse sensor. I have been meaning to change it for a long time but kept putting it off. So one day I drove down to the Brother's outlet near my house in PJ. However, the place was packed and I could not get any parking. I was impatient and decided to go to another car accessories place - Elegance Audio Sdn Bhd. in Kelana Jaya.

I was delighted because there were not that many customers around. Their manager Oliver Lim, came out and told me that it would cost me around RM200+ to install new reverse sensors. This was much costlier than what it would normally cost me at Brothers but I assumed that at that price their product would be of a better quality than at Brothers, which was where I had installed my old reverse sensors.

Since the shop was specialised in audio equipment and I was still under budget, I decided to install front speakers in the car. Previously it only had 2 rear Clarion speakers. The cheapest speakers was the Powerbass S-4002 4-Inch Coaxial speakers (105 W), at around RM260 a pair. A little bit steep but he assured me that the sound quality would be really great. This would nicely bring me just below my budget of a Thousand dollars and I decided to go ahead.


However, this is where it all went wrong. I was waiting inside their office with my son when the manager came in and showed me the old speakers - it was completely torn. I knew it was old but I am sure it was definitely not that bad. I now had no choice but to replace the rear speakers as well. I went along with what the manager recommended and installed a pair of EFX 6x9" rear speakers (RM480).

I was dismayed when I learnt that as the new speakers would not fit into the original speaker enclosure and they would have to cut into the rear speaker board. I wished the manager had explained that to me before I said yes.





The final damage - a whooping RM1020 in total, including the installation charges. These three items alone would have blown my small budget of RM1K at one go.

In hindsight, I could have said "No!" and this would have left me with a total budget of RM903.9. I could have then gone to Brothers and have cheaper speakers installed. But that is what you call "buyer's remorse" and I am trying hard not to have any regrets. However, I hope other people reading this would learn from my experience and make an informed choice.

I am sure that some of you are wondering "what's the difference"?

Now, I do notice that I don't have to crank up the volume and sound quality has definitely improved but no once else - neither my family members nor my friends seems to have realised the difference. The only guy who noticed is my son who went along with me and tries to put peanuts and other stuff into the holes in the speaker covers - a clear design flaw if you have hyperactive kids with itchy hands.

So my budget is blown and I have failed in my project. It was stupid anyway as an old car needs constant attention and replacement of parts. In conclusion, RM1000 goes a bit but is but a drop in the ocean if you decide to hold on to an old car and decide to "pimp it". However, on the other hand, well maintained cars can go a long way and is considerably cheaper than getting a brand new car - specially if you live in Malaysia.


This is the article Proton Wira modifications under RM1K project: Part 2

It's an article Proton Wira modifications under RM1K project: Part 2 this time, I hope you will all benefit. Ok, see you soon in another article.

You are reading the article Proton Wira modifications under RM1K project: Part 2 with the link address https://carsgalleryonline.blogspot.com/2015/08/proton-wira-modifications-under-rm1k.html

Comments